Ammonia to hydrogen equivalent: mass, recovery and delivery
One metric tonne of pure ammonia contains about 177.6 kg of hydrogen by mass. Recoverable hydrogen depends on the conversion and separation process. For liquid hydrogen, start with the hydrogen mass actually delivered, then keep earlier storage or handling losses separate.
Convert ammonia mass before comparing supply volumes
An ammonia contract specifies ammonia mass, not hydrogen mass. NIST lists ammonia as H₃N with a molecular weight of 17.0305, and hydrogen as H₂ with a molecular weight of 2.01588. These values give the chemical hydrogen content of pure ammonia.
The balanced decomposition is 2 NH₃ → N₂ + 3 H₂. Divide three times the molecular weight of hydrogen by twice that of ammonia. The hydrogen mass fraction is approximately 0.177553, or 17.7553%. This is a chemical-content calculation before process losses.
Using the unrounded fraction, 1,000 kg of pure ammonia contains 177.553 kg of hydrogen, shown here as 177.6 kg. Conversely, 1 kg of hydrogen requires at least about 5.632 kg of pure ammonia at complete conversion and recovery. Moisture, impurities or a different product specification require an adjusted basis.
Theoretical H₂ mass = pure NH₃ mass × [3 × 2.01588 ÷ (2 × 17.0305)]
Sources
National Institute of Standards and Technology
NIST Chemistry WebBook, SRD 69: Ammonia
Formula and molecular weight: H₃N; 17.0305
Last confirmed: 2026-11-16
National Institute of Standards and Technology
NIST Chemistry WebBook, SRD 69: Hydrogen
Formula and molecular weight: H₂; 2.01588
Last confirmed: 2026-11-16
State recovery assumptions separately
Chemical content does not specify the output a cracking and separation system will deliver. Ask for the boundary: ammonia entering the process, hydrogen formed, hydrogen separated to specification, and hydrogen measured at the customer. Use a performance figure covering the boundary you need.
For a fictional example, assume 80% of the chemical hydrogen content reaches the delivery meter. A 1,000 kg ammonia input then yields an estimated 142.0 kg of delivered hydrogen. The 80% value is an example input, not an industry average or an equipment guarantee.
If a supplier gives separate conversion and separation-recovery rates, check their denominators before multiplying them. An overall delivered-recovery figure may already include both effects. Applying the same loss twice would understate output.
Est. delivered H₂ = theoretical H₂ content × overall delivered-recovery fraction
Illustrative mass comparison; assumed recoveries are not equipment benchmarks
| Input or measurement | Explicit basis | Hydrogen quantity |
|---|---|---|
| 1,000 kg pure ammonia | Complete conversion and recovery | 177.6 kg theoretical H₂ |
| 1,000 kg pure ammonia | Assumed 80% overall delivered recovery | Est. 142.0 kg delivered H₂ |
| 1,000 kg pure liquid hydrogen at the delivery meter | Mass measured at that delivery boundary | 1,000 kg delivered H₂ |
| 1,000 kg pure liquid hydrogen before handling | Assumed 95% of initial mass delivered | Est. 950 kg delivered H₂ |
Ammonia calculations use 3 × 2.01588 ÷ (2 × 17.0305) before rounding. The 80% and 95% cases are fictional assumptions. These rows do not estimate process energy or total supply cost.
Sources
National Institute of Standards and Technology
NIST Chemistry WebBook, SRD 69: Ammonia
Formula and molecular weight: H₃N; 17.0305
Last confirmed: 2026-11-16
National Institute of Standards and Technology
NIST Chemistry WebBook, SRD 69: Hydrogen
Formula and molecular weight: H₂; 2.01588
Last confirmed: 2026-11-16
Keep liquid hydrogen mass and volume distinct
Liquid hydrogen is hydrogen in a different physical state, rather than hydrogen chemically bound in ammonia. Under the pure-product assumption, its hydrogen-equivalent mass equals its mass. A tonne of liquid hydrogen represents a tonne of hydrogen at that measurement boundary.
A tank volume is a different input. Converting litres or cubic metres to mass requires a density corresponding to the stated physical conditions. A normal gas-volume conversion factor does not describe liquid density.
Request the delivered mass at the named meter and the accounting period. If your starting figure precedes storage or transport, use a documented delivered-mass measurement or an explicit loss assumption. This guide does not supply a typical boil-off rate, storage duration or liquefaction-energy allowance.
Sources
National Institute of Standards and Technology
NIST Chemistry WebBook, SRD 69: Hydrogen
Formula and molecular weight: H₂; 2.01588
Last confirmed: 2026-11-16
Use hydrogen equivalent as one comparison step
A hydrogen-equivalent calculation changes a price denominator. In a fictional purchase at 500 USD per tonne of pure ammonia, the feedstock alone costs an estimated 2.82 USD per theoretical kg of hydrogen. At the assumed 80% delivered recovery, the same purchase costs an estimated 3.52 USD per delivered kg before other costs.
These examples divide 500 USD by 177.553 kg and 142.043 kg respectively. They exclude conversion equipment, energy, storage, transport, financing and other costs. They are arithmetic examples, not quotations or market forecasts.
Before comparing offers, align product, mass unit, time period, delivery location and conversion boundary. Keep energy input and product energy content in separate calculations with their own stated basis. Ammonia used directly as a product or fuel should not be described as a measured delivery of separated hydrogen.
Est. ammonia feedstock cost per delivered kg H₂ = ammonia purchase cost ÷ H₂ delivered from that purchased quantity
Sources
National Institute of Standards and Technology
NIST Chemistry WebBook, SRD 69: Ammonia
Formula and molecular weight: H₃N; 17.0305
Last confirmed: 2026-11-16
National Institute of Standards and Technology
NIST Chemistry WebBook, SRD 69: Hydrogen
Formula and molecular weight: H₂; 2.01588
Last confirmed: 2026-11-16
Common questions
How much hydrogen is in one tonne of ammonia?
About 177.6 kg by chemical mass content for pure ammonia, calculated from the NIST molecular weights. Delivered hydrogen requires a stated conversion and recovery boundary.
Is 80% the normal ammonia-to-hydrogen recovery rate?
No. It is a fictional input showing the calculation. Use a project-specific measured or guaranteed value covering the delivery boundary you need.
Can I convert liquid hydrogen litres directly to kilograms?
Only with a liquid density appropriate to the stated physical conditions. A normal gas-volume conversion factor does not describe liquid hydrogen.
Does hydrogen-equivalent mass describe the full delivered cost?
No. It aligns a mass denominator. A delivered-cost comparison also needs relevant conversion, energy, storage, transport and other costs.