H2PrismHydrogen intelligenceSubscribe

← All calculators

CalculatorsHydrogen Converter

Hydrogen Converter

Converts hydrogen amount, flow & capacity, pressure, reference state, price unit, and carrier (ammonia, liquid hydrogen, methanol) quantities between units.

Convert a hydrogen quantity while keeping its energy basis and reference conditions visible. Separate tabs cover mass and energy, flow, pressure, gas conditions, prices and carriers.

How the calculation works

Energy equals hydrogen mass times the selected heating value. Reference gas volume equals mass times the stated volume factor. Flow uses the same factors per hour. Gas-state conversion uses V2 = V1 × P1/P2 × T2/T1 × Z2/Z1, with absolute pressure and temperature in kelvin. Carrier calculations apply the displayed mass ratio, conversion and recovery inputs.

Inputs and defaults

The amount tab starts at 100 kg, flow at 1,000 kg/h and pressure at 350 bar(a). Built-in factors include 33.3 kWh/kg LHV, 39.4 kWh/kg HHV and 11.126 Nm³/kg at 0°C and 1 atm. The 15°C factor is 11.736392 m³/kg. Arbitrary-state compressibility factors start at 1. Carrier conversion, recovery and process-energy inputs include illustrative assumptions.

Assumptions and limits

A normal cubic metre has stated temperature and pressure. Do not use it as an actual vessel volume at high pressure. Gas-state conversion with Z = 1 is an ideal-gas approximation. Liquid-hydrogen boil-off is linear in daily loss rate times storage days; liquefaction electricity applies to the initial mass. Carrier process-energy assumptions do not constitute a complete plant or delivered-cost model.

Price and flow boundaries

A hydrogen price per kg converts to price per MWh as price/kg × 1,000 ÷ the selected heating value in kWh/kg. Electricity cost per kg is electricity price/MWh × system SEC ÷ 1,000. This electricity-only amount excludes capital and other operating costs. Electrical input power equals kg/h × system SEC ÷ 1,000; hydrogen thermal power instead uses its heating value.

Ammonia and methanol calculations

Ammonia cracking uses recovered hydrogen = ammonia mass × hydrogen mass fraction × conversion × recovery. Synthesis uses ammonia mass = hydrogen input × utilization ÷ hydrogen mass fraction. The fixed hydrogen fraction is 0.1776; molar-mass mode calculates the fraction instead. Cracking conversion and recovery start at 99% each. The heat and electricity assumptions are 9.7 and 1.5 kWh per kg recovered hydrogen. Synthesis starts at full utilization and 0.566 kWh per kg ammonia. These process inputs are illustrative, not confirmed representative plant data.

Methanol and liquid-hydrogen boundaries

Methanol synthesis hydrogen demand equals target methanol mass × [3 × M(H₂)/M(CH₃OH)] ÷ (conversion × recovery); the CO₂ demand uses M(CO₂)/M(CH₃OH). Conversion and recovery start at 1, with 1.25 kWh/kg methanol process electricity. Reforming applies conversion and recovery to the theoretical hydrogen mass; defaults are 95% and 90%, with 12.9 kWh heat and 0.5 kWh electricity per kg recovered hydrogen. Process-energy defaults have an unconfirmed external basis or are examples. The liquid-hydrogen example starts at 1,000 kg and 10 days, using a conservative example loss rate of 0.1%/day and 10 kWh/kg initial mass for liquefaction. Loss is calculated linearly, not compounded. None of these calculations is a complete delivery-chain energy model.

Frequently asked questions

Why do LHV and HHV give different energy values?

HHV includes the heat recovered when product water condenses. Keep the same heating-value basis when comparing quantities or efficiencies.

Can I convert Nm³ directly to tank volume?

Use the stated reference condition for Nm³. To estimate storage volume, use the hydrogen storage calculator with an appropriate density.

Does ammonia mass equal recoverable hydrogen mass?

No. The built-in hydrogen mass fraction is 0.1776. Cracking output also depends on the selected conversion and hydrogen recovery assumptions.

Are carrier process-energy defaults measured plant data?

Several carrier inputs are illustrative or have an unconfirmed external basis. Check the input detail and replace them with project-specific values.

Does a price per MWh represent production cost?

It is a unit conversion of the entered hydrogen price. The electricity-cost calculation is a separate electricity-only amount. Use the hydrogen price calculator for a defined production-cost model.

Sources